深圳市福田区新宏舟电子经营部

SMD Aluminum Electrolytic Capacitors
2012E2 45
VE Series
Features
‧3φ ~ 18φ, 85℃, 2,000 hours assured
‧Chip type large capacitance capacitors
‧Designed for surface mounting on high density PC board
‧RoHS Compliance
Marking color: Black
Specifications
Items Performance
Category Temperature Range -40℃ ~ +85℃
Capacitance Tolerance ±20% (at 120Hz, 20℃)
Rated Voltage 6.3 ~ 100V 160 ~ 450V
Time after 2 minutes after 5 minutes
Leakage Current (at 20℃) Case size 3 ~ 10φ 12.5 ~ 18φ 12.5 ~ 18φ
Leakage Current I = 0.01CV or 3μA,
whichever is greater
I = 0.03CV or 4μA,
whichever is greater I = 0.04CV +100μA
Where, C = rated capacitance in μF V = rated DC working voltage in V
Dissipation Factor Rated Voltage 4 6. 100 160 ~ 250 400 ~ 450
(Tanδ at 120Hz, 20℃) 3 ~ 10φ 0.42 0.28 0.24 0.20 0.14 0.12 0.10 0.10 0.10 - -
12.5 ~ 18φ - 0.38 0.34 0.30 0.26 0.22 0.18 0.14 0.10 0.20 0.25
When the capacitance exceeds 1,000μF, 0.02 shall be added every 1,000μF increase.
Impedance ratio shall not exceed the values given in the table below.
Rated Voltage 4.0 6. 100 160 ~ 250 400 ~ 450
Low Temperature Z(-25℃) φD＜12. 2 2 2 2 - -
Characteristics (at 120Hz) Impedance /Z(+20℃) φD≧12.5
Ratio Z(-40℃) φD＜12. - -
/Z(+20℃) φD≧12.5 6 10
Test Time 2,000 Hrs
Capacitance Change Within ±20% of initial value (4V: ±30%)
Endurance Dissipation Factor Less than 200% of specified value (4V: ±300%)
Leakage Current Within specified value
* The above Specifications shall be satisfied when the capacitors are restored to 20℃after the rated voltage applied for 2,000
hours at 85℃.
Shelf Life Test Test time: 1,000 hours; other items are the same as those for the Endurance.
The rated voltage shall be applied to the capacitors before the measurements for 160 ~ 450V (Refer to JIS C 5101-4 4.1).
Ripple Current & Freq. (Hz)
Cap. (μF)k 10k up
Frequency Multipliers Under 1,000 0.80 1.00 1.25 1.40
1,000 ＜ C ≦ 6,800 0.85 1.00 1.15 1.25
Diagram of Dimensions
Fig. 1 Lead Spacing and Diameter Unit: mm
φD L A B C W P ± 0.2 Fig. No.
3 5.3 ± 0.2 3.3 3.3 4.1 0.45 ~ 0.75 0.8 1
4 5.3 ± 0.2 4.3 4.3 5.1 0.5 ~ 0.8 1.0 1
5 5.3 ± 0.2 5.3 5.3 5.9 0.5 ~ 0.8 1.5 1
6.3 5.3 ± 0.2 6.6 6.6 7.2 0.5 ~ 0.8 2.0 1
6.3 7.7 ± 0.3 6.6 6.6 7.2 0.5 ~ 0.8 2.0 1
8 10 ± 0.5 8.4 8.4 9.0 0.7 ~ 1.1 3.1 1
Fig. 2 8 10.3 ± 0.5 8.4 8.4 9.0 0.7 ~ 1.1 3.1 1
10 7.7 ± 0.3 10.4 10.4 11.0 0.7 ~ 1.3 4.7 1
10 10 ± 0.5 10.4 10.4 11.0 0.7 ~ 1.3 4.7 1
10 10.3 ± 0.5 10.4 10.4 11.0 0.7 ~ 1.3 4.7 1
12.5 13.5 ± 0.5 13.0 13.0 13.7 1.1 ~ 1.4 4.4 2
12.5 16 ± 0.5 13.0 13.0 13.7 1.1 ~ 1.4 4.4 2
16 16.5 ± 0.5 17.0 17.0 18.0 1.1 ~ 1.4 6.4 2
16 21.5 ± 0.5 17.0 17.0 18.0 1.1 ~ 1.4 6.4 2
18 16.5 ± 0.5 19.0 19.0 20.0 1.1 ~ 1.4 6.4 2
18 21.5 ± 0.5 19.0 19.0 20.0 1.1 ~ 1.4 6.4 2
B±0.2
P
φD±0.5
L
0.3 Max
A±0.2
W
C±0.2
0.4 max
Vent≧8φ×10L
φD±0.5
P
1.0 Max
W
C±0.2
L
0.4 Max
A±0.2 B±0.2
Vent
VE

详见：LELON PDF文件。